Using STARMOBILE

1. Install a battery charger and verify that the charging rate provides 13.0 to 13.5 volts. Do not allow the charger to time out during the flash process. Set the battery charger timer (if so equipped) to continuous charge.

2. Connect the CH9410 StarMOBILE ethernet cable to the StarMOBILE and the dealer's network drop.

3. Connect the CH9404 StarMOBILE vehicle cable to the StarMOBILE and the vehicle.

4. Place the Ignition in the "RUN" position, then Power "ON" the StarMOBILE.

5. Record the StarMOBILE I.P. address displayed on the StarMOBILE screen.

6. From the desktop, launch the "StarMOBILE Desktop Client" software.

7. Establish a connection with the StarMOBILE scan tool.

8. Download the flash file from the internet to the StarMOBILE. With the StarMOBILE on the "Home" screen, follow the procedure below:

a. Select "ECU View".

b. Touch the screen to highlight "PCM" in the list of modules.

c. Select "More Options".

d. Select "ECU Flash".

e. Select "Browse for New File".

f. Enter Identification name and password.

g. Press "Finish".

h. Highlight the appropriate calibration based on the part number recorded in Step 2k. of the PCM replacement procedure for StarMOBILE.

i. Select "Download to Client".

j. Select "Close" after the download is complete, then select "Back".

k. Highlight the listed calibration.

l. Select "Update Controller" and follow the on screen instructions.

m. When the update is completed, select "OK".

n. Verify that the part number at the top of the Flash PCM screen has updated to the new part number.

9. Vehicles equipped with a Wireless Control Module (WCM), perform the following procedure:

a. Starting at the "Home" screen, select "ECU View".

b. Select "WCM Wireless Control".

c. Select "Misc. Functions".

d. Scroll down the list and select "PCM Replaced".

e. Press the blue "Start" button on the Desktop Client.

f. Press the "Next" button on the Desktop Client.

g. Enter the Personal Identification Number (PIN) for that vehicle

NOTE:
The PIN number can be obtained from the original selling invoice, DealerCONNECT > Parts > Key Codes, or contacting the District Manager.

h. Follow the screen prompts to complete the process.

i. Remove the ignition key from the ignition for one minute.

CAUTION:
Failure to remove the key from the ignition for one minute may cause a "No Crank" condition.

j. Insert the key and place the ignition in the "Run" position.

k. Continue with Step 11 of this procedure.

10. Vehicles not equipped with a Wireless Control Module, perform the following procedure:

a. Starting at the "Home" screen, select "ECU View".

b. Select "PCM".

c. Select "Misc. Functions".

d. Select "Check PCM VIN" and follow the on screen instructions.

e. When complete, select "Finish".

11. Perform the learn Electronic Throttle Control (ETC) programming using the following procedure:

a. From the "Home" screen, select "ECU View".

b. Select "PCM".

c. Select "Misc. Functions".

d. Select "Learn ETC" and press the "Start" button on the Desktop Client.

e. Follow the screen prompts to complete the process.

12. Check the PCM Odometer programming using the following procedure:

a. From the "Home" screen, select "ECU View".

b. Select "PCM".

c. Select "Misc. Functions".

d. Select "Check PCM Odometer" and press the "Start" button on the Desktop Client.

e. Follow the on screen instructions.

f. When complete, select "Finish".

13. Place the Ignition in the "OFF" position, then Power "Off" the StarMOBILE.

14. Disconnect the Data Link Connector (DLC), wait 15 seconds, and reconnect the DLC to the vehicle.

15. Place the ignition in the "RUN" position, power "ON" the StarMOBILE and restart the Desktop Client.

16. Vehicles equipped with a four-speed transaxle, perform Transmission Control Module (TCM) Quicklearn programming using the following procedure:

a. From the "Home" screen, select "ECU View".

b. Select "TCM Transmission Control Module".

c. Select "Misc. Functions".

d. Select "Quicklearn" and press the "Start" button on the Desktop Client.

e. Follow the on screen instructions.

f. When complete, select "Finish".

17. Clear any Diagnostic Trouble Codes (DTCs) as follows:

NOTE:
Due to the PCM programming procedure, DTC(s) may be set in other modules (TCM, ABS, BCM, MIC, WCM, etc.) within the vehicle, if so equipped. Some DTC's may cause the MIL to illuminate.

a. From the "Home" screen select "System View".

b. Select "All DTCs".

c. Press "Clear All Stored DTCs" if there are any DTCs shown on the list.

d. Follow the on screen instructions.

18. Turn the ignition key to the "OFF" position and remove the StarMOBILE unit, StarMOBILE cable, and battery charger from the vehicle.

19. Continue with Section C. Install Authorized Modifications Label.