Curiosii for ever!: Car repair manuals for everyone.
Home >> Toyota >> 2010 >> Yaris L4-1.5L (1NZ-FE) >> Repair and Diagnosis >> A L L Diagnostic Trouble Codes ( DTC ) >> Testing and Inspection >> P Code Charts >> P0452

P0452





1NZ-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0450-P0453: Evaporative Emission Control System Pressure Sensor / Switch


DTC SUMMARY





HINT
The canister pressure sensor is built into the canister pump module.

DESCRIPTION

The description can be found in the EVAP (Evaporative Emission) System Component Tests and General Diagnostics.

HINT
Unit expressions

- [kPa-a (mmHg-a)] denotes the absolute pressure.
- [kPa-g (mmHg-g)] denotes the gauge pressure (relative pressure).
- On a Techstream, convert the unit of measurement according to the inspection procedure.
MONITOR DESCRIPTION





* DTC P0450: Canister pressure sensor voltage abnormal fluctuation

* If the canister pressure sensor voltage output [pressure] rapidly fluctuates between less than 0.45 V [42.1 kPa-a (315.9 mmHg-a)] and more than 4.9 V [123.8 kPa-a (928.4 mmHg-a)], the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit, and stops the EVAP (Evaporative Emission) system monitor. The ECM then illuminates the MIL and sets the DTC (1 trip detection logic).

* DTC P0451: Canister pressure sensor noise or fixed/flat

* If the canister pressure sensor voltage output fluctuates rapidly for 10 seconds, the ECM stops the EVAP system monitor. The ECM interprets this as noise from the canister pressure sensor, and stops the EVAP system monitor. The ECM then illuminates the MIL and sets the DTC.

* Alternatively, if the sensor voltage output does not change for 10 seconds, the ECM interprets this as the sensor being fixed/flat, and stops the monitor. The ECM then illuminates the MIL and sets the DTC.

* (Both the malfunctions are detected by 2 trip detection logic).

* DTC P0452: Canister pressure sensor voltage low

* If the canister pressure sensor voltage output [pressure] is below 0.45 V [42.1 kPa-a (315.9 mmHg-a)], the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and sets the DTC (1 trip detection logic).

* DTC P0453: Canister pressure sensor voltage high

* If the canister pressure sensor voltage output [pressure] is 4.9 V [123.8 kPa-a (928.4 mmHg-a)] or more, the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and sets the DTC (1 trip detection logic).

MONITOR STRATEGY





TYPICAL ENABLING CONDITIONS

P0451 (Noise monitor):

P0451 (Noise monitor)::





P0451 (Fixed/flat monitor):

P0451 (Fixed/flat monitor)::





P0450, P0452 and P0453:

P0450, P0452 and P0453::





TYPICAL MALFUNCTION THRESHOLDS

P0450: Canister pressure sensor chattering

P0450: Canister pressure sensor chattering:





P0451: Canister pressure sensor noise

P0451: Canister pressure sensor noise:





P0451: Canister pressure sensor fixed/flat

P0451: Canister pressure sensor fixed/flat:





P0452: Canister pressure sensor low voltage

P0452: Canister pressure sensor low voltage:





P0453: Canister pressure sensor high voltage

P0453: Canister pressure sensor high voltage:





CONFIRMATION DRIVING PATTERN





NOTICE:
- The Evaporative System Check (Automatic Mode) consists of 5 steps performed automatically by the Techstream. It takes a maximum of approximately 19 minutes.
- Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.
- Do not run the engine during this operation.
- When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F).
* Connect the Techstream to the DLC3.

* Turn the ignition switch to ON and turn the Techstream on.

* Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

* Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

* Turn the ignition switch off and wait for at least 30 seconds.

* Turn the ignition switch to ON and turn the Techstream on [A].

* Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.

* After the "Evaporative System Check" is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

* Input the DTC: P0450, P0451, P0452 or P0453.

* Check the DTC judgment result [B].





HINT
If the judgment result shows ABNORMAL, the system has a malfunction.

* If the result is INCOMPLETE or UNKNOWN and no pending DTC is output, perform a universal trip and check for permanent DTCs DTC Check / Clear.

HINT
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTC is output, the system is normal.
WIRING DIAGRAM





INSPECTION PROCEDURE

NOTICE:
- When a vehicle is brought into the workshop, leave it as it is. Do not change the vehicle condition. For example, do not tighten the fuel cap.
- Do not disassemble the canister pump module.
- A Techstream is required to conduct the following diagnostic troubleshooting procedure.
PROCEDURE

1. CONFIRM DTC AND EVAP PRESSURE

(a) Connect a Techstream to the DLC3.

(b) Turn the ignition switch to ON (do not start the engine).

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

(e) Read DTCs.

(f) Enter the following menus: Powertrain / Engine and ECT / Data List / EVAP / Vapor Pressure Pump.

(g) Read the EVAP (Evaporative Emission) pressure displayed on the Techstream.

Result:





C -- GO TO EVAP SYSTEM Component Tests and General Diagnostics

B -- CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
A -- Continue to next step.

2. CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)





(a) Turn the ignition switch off.

(b) Disconnect the C20 ECM connector.

(c) Check the resistance between PPMP terminal of the ECM connector and the body ground.

Result:





(d) Reconnect the ECM connector.

B -- REPLACE ECM
A -- Continue to next step.

3. CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)





(a) Disconnect the J25 canister pump module connector.

(b) Disconnect the C20 ECM connector.

(c) Check the resistance between PPMP terminal of the ECM connector and the body ground.

Result:





(d) Reconnect the canister pump module connector.

(e) Reconnect the ECM connector.

B -- REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)

A -- REPLACE CANISTER

1. CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)





(a) Disconnect the J25 canister pump module connector.

(b) Turn the ignition switch to ON.

(c) Measure the voltage and resistance of the canister connector.

Standard:





Result:





(d) Reconnect the canister pump module connector.

B -- REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)

A -- REPLACE CANISTER

2. REPLACE CANISTER

(a) Replace the canister assembly Removal.

NOTICE:
When replacing the canister, check the canister pump module interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose.





NEXT -- CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)

3. REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)

HINT
If the exhaust tail pipe has been removed, go to the next step before reinstalling it.

NEXT -- CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)

4. REPLACE ECM

(a) Replace the ECM Removal.

NEXT -- CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)

5. CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Clear the DTCs DTC Check / Clear.

(e) Turn the ignition switch off and wait for at least 30 seconds.

(f) Turn the ignition switch to ON and turn the Techstream on.

(g) Start the engine and warm it up.

(h) Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

(i) Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

(j) Input the DTC: P0451, P0452 or P0453.

(k) Check the DTC judgment result.





NEXT -- END
pro multis · Curiosii