Installation

STEERING COLUMN: STEERING COLUMN ASSEMBLY: INSTALLATION

INSTALLATION





1. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT
(a) Align the part of the dust cover labeled A with the No. 2 steering intermediate shaft, and install the No. 2 steering intermediate shaft assembly to the steering link assembly.
(b) Install the bolt.
Torque: 35 Nm (360 kgf-cm, 26 ft-lbf)
NOTE: Be careful not to damage the dust cover.

2. INSTALL STEERING COLUMN HOLE COVER SUB-ASSEMBLY






(a) Install the 4 bolts and nut.
Torque: 5.0 Nm (51 kgf-cm, 44 in-lbf)
NOTE: Do not fold back the boot part of the steering hole cover or extend it excessively. if it is extended excessively, return it to its original position.
HINT: Install the steering intermediate shaft assembly from the inside of the vehicle.

(b) Install the clamp to the steering column hole cover.
3. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY






(a) Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering intermediate shaft assembly.
HINT: Install the steering intermediate shaft from the inside of the vehicle.

(b) Install the bolt.
Torque: 35 Nm (360 kgf-cm, 26 ft-lbf)
4. INSTALL STEERING COLUMN ASSEMBLY





(a) Align the matchmarks on the steering intermediate shaft and the steering column.
(b) Install the bolt.
Torque: 35 Nm (360 kgf-cm, 26 ft-lbf)






(c) Install the steering column with the 4 nuts.
Torque: 26 Nm (265 kgf-cm, 19 ft-lbf)
5. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY Installation







6. CONNECT WIRE HARNESS PROTECTOR AND WIRE HARNESS
(a) Attach the 3 claws to connect the wire harness protector and wire harness.
7. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY Installation

8. INSTALL NO. 1 SWITCH HOLE BASE Installation

9. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL Installation

10. INSTALL COWL SIDE TRIM BOARD LH Installation

11. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Installation

12. INSTALL FRONT DOOR SCUFF PLATE LH Removal

13. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY Installation

14. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH Installation

15. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH Installation

16. INSTALL INSTRUMENT SIDE PANEL LH Installation

17. INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH Installation

18. INSTALL NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION Installation

19. INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY





(a) Using pliers, grip the claws of the clamp and install the combination switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.






(b) Connect the 5 connectors to the combination switch with spiral cable.






20. INSTALL TILT AND TELESCOPIC MANUAL SWITCH
(a) Attach the claw to install the switch.
(b) Connect the switch connector.






21. INSTALL UPPER STEERING COLUMN COVER
(a) Attach the claw.
(b) Attach the 4 clips to install the upper steering column cover onto the instrument cluster finish panel.






22. INSTALL LOWER STEERING COLUMN COVER
(a) Attach the 2 claws to install the lower steering column cover.
NOTE: Do not damage the tilt and telescopic switch.

(b) Install the 3 screws.
Torque: 1.5 Nm (15 kgf-cm, 13 in-lbf)
23. INSTALL STEERING WHEEL ASSEMBLY Installation

24. INSTALL STEERING PAD Installation

25. INSTALL LOWER NO. 2 STEERING WHEEL COVER Installation

26. INSTALL LOWER NO. 3 STEERING WHEEL COVER Installation

27. CHECK FRONT WHEELS FACING STRAIGHT AHEAD
28. INSTALL FRONT WHEELS
29. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTE: Reset the AUTO TILT AWAY function setting to the previous condition by changing the customize parameter Programming and Relearning.

30. INSPECT SRS WARNING LIGHT
(a) Inspect the SRS warning light Diagnosis System.