P0172

Diagnostic Chart (Part 1 Of 2):

Diagnostic Chart (Part 2 Of 2):

CIRCUIT DESCRIPTION
To provide the best possible combination of driveability, fuel economy, and emission control, a closed loop air and fuel metering system is used. While in closed loop, the PCM monitors the HO2S 1 signal and adjusts fuel delivery based upon the HO2S signal voltage. A change in the fuel delivery will be indicated by changes in the long and short term fuel trim values. The fuel trim values can be monitored with a scan tool. Ideal fuel trim values are approximately 0 percent. If the HO2S signals indicate a lean condition, the PCM will add fuel, resulting in fuel trim values of more than 0 percent. If a rich condition is detected, the fuel trim values will be less than 0 percent, indicating that the PCM is reducing the amount of fuel delivered. If an excessively rich condition is detected, the PCM will set DTC P01712.

The PCM's maximum authority to control long term fuel trim allows a range between -23 percent and +16 percent. The PCM's maximum authority to control short term fuel trim allows a range between -11 percent and +20 percent. The PCM monitors fuel trim under various operating conditions - or fuel trim cells - before determining the status of the fuel trim diagnostic. The fuel trim cells used to determine the fuel trim are as follows:
^ Idle, purge commanded: Cell 10.
^ Deceleration, purge commanded: Cell 1.
^ Normal driving, purge commanded: Cell 2.
^ Deceleration, no purge commanded: Cell 5.
^ Normal driving, no purge commanded: Cell 6.
^ Idle, no purge commanded: Cell 9.

The vehicle may have to be operated in all of the above conditions before the PCM determines fuel trim status. The amount that fuel trim deviates from 0 percent in each cell, and the amount that each cell is weighted directly affects whether or not the vehicle must be operated in all of the cells described above to complete the diagnostic.

CONDITIONS FOR RUNNING THE DTC
^ There are no active DTCs of any of the following types present:
^ Fuel trim
^ Fuel injector circuit
^ Ignition control circuit
^ Misfire
^ Idle speed
^ Evaporative Emission (EVAP)
^ Heated Oxygen Sensor (HO2S)
^ Exhaust Gas Recirculation (EGR)
^ Secondary Air Injection system (AIR)
^ Vehicle Speed Sensor (VSS)
^ Throttle Position (TP) sensor
^ Intake Air Temperature (IAT) sensor
^ Manifold Absolute Pressure (MAP) sensor
^ Engine Coolant Temperature (ECT) sensor
^ Crankshaft Position (CKP) sensor
^ Camshaft Position (CMP) sensor
^ Mass Air Flow (MAF) sensor
^ The ECT is between 20°-110°C (68°-230°F).
^ The IAT is between -18°C and +70°C (0°-158°F).
^ The BARO is more than 70 kPa (10.15 psi).
^ The MAP is between 15-85 kPa (2.175-12.327 psi).
^ The throttle angle is less than 50 percent.
^ The vehicle speed is less than 133.57 km/h (83.0 mph).
^ The MAF is between 3-150 g/s.
^ The engine speed is between 600-4000 RPM.

CONDITIONS FOR SETTING THE DTC
^ The long term fuel trim is at or near the maximum authority of -23 percent.
^ The short term fuel trim is at or near the maximum authority of -11 percent.
^ All of the necessary conditions have been met in fuel trim cells 1, 2, 5, 6, 9 and/or 10.

ACTION TAKEN WHEN THE DTC SETS
^ The PCM illuminates the Malfunction Indicator Lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
^ The PCM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the PCM stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the PCM records the operating conditions at the time of the failure. The PCM writes the conditions to the Freeze Frame and updates the Failure Records.

CONDITIONS FOR CLEARING THE MIL/DTC
^ The PCM turns the MIL OFF after three consecutive drive trips during which the diagnostic runs and passes.
^ A last test failed, or the current DTC, clears when the diagnostic runs and passes.
^ A History DTC clears after forty consecutive warm-up cycles, if no other emission related diagnostic failures are reported.
^ Use a scan tool in order to clear the MIL diagnostic trouble code.
^ Interrupting the PCM battery voltage may or may not clear DTCs. This practice is not recommended. Refer to Powertrain Control Module (PCM) Description, Clearing Diagnostic Trouble Codes.

DIAGNOSTIC AIDS

NOTE: Refer to Connector Test Adapter Kit J 35616-A Notice in Service Precautions.

Check the following components and conditions:
^ The fuel pressure - The system may become rich if the pressure is too high. The PCM can compensate for some increase. However, if the fuel pressure is too high, a DTC P0172 may set. Refer to Fuel System Pressure Test. Fuel System Pressure Test
^ The fuel injectors - Refer to Fuel Injector Coil Test - Engine Coolant Temperature (ECT) Between 10-35 Degrees C (50-95 Degrees F) or Fuel Injector Coil Test - Engine Coolant Temperature (ECT) Outside 10-35 Degrees C (50-95 Degrees F). Component Tests and General Diagnostics Component Tests and General Diagnostics
^ The EVAP canister - Check the EVAP canister for fuel saturation. If the canister is full of fuel, visually and physically check the EVAP and fuel system components for damage. Refer to Service Bay Test. Component Tests and General Diagnostics
^ The mass air flow sensor - Disconnect the MAF sensor and see if the rich condition is corrected. If so, replace the MAF sensor.
^ The fuel pressure regulator: - Check for a leaking fuel pressure regulator diaphragm by checking the vacuum line to the regulator for the presence of fuel. If a problem is found, replace the fuel pressure regulator.
^ The TP sensor - An intermittent TP sensor output will cause the system to become rich due to a false indication of the engine accelerating. The Throttle Angle displayed on a scan tool should increase steadily from 0-100 percent when opening the throttle. If this does not occur, check the TP sensor for loose mounting screws. If the TP mounting screws are OK, replace the TP sensor.

Reviewing the Failure Records vehicle mileage since the diagnostic test last failed may help determine how often the condition occurs that caused the DTC to set. This may assist in diagnosing the condition.

If the problem is intermittent, refer to Intermittent Conditions. Intermittent Conditions

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
2. DTCs other than P0172 may indicate that a condition is present that may be causing a rich condition. If this is the case, repairing the condition that caused the other DTC will most likely correct DTC P0172.
4. If the DTC P0172 test passes while the Fail Records conditions are being duplicated, the rich condition is intermittent. Refer to Diagnostic Aids for additional information on diagnosing intermittent conditions.