Installation
WIPER / WASHER: FRONT WIPER MOTOR: INSTALLATION
1. INSTALL WIPER MOTOR WIRE
(a) Attach the claw to install the wiper motor wire.
2. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
(a) Using a T30 "TORX" socket, install the wiper motor with the 2 bolts.
Torque : 7.5 Nm (76 kgf-cm, 66 in-lbf)
(b) Connect the connector.
(c) Apply MP grease to the crank arm pivot of the front wiper crank.
Text in Illustration
(d) Connect the rod to the crank arm pivot of the front wiper crank.
3. INSTALL WINDSHIELD WIPER MOTOR AND LINK
(a) Attach the grommet as shown in the illustration.
Torque : 7.0 Nm (71 kgf-cm, 62 in-lbf)
Text in Illustration
NOTICE:
Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.
(b) Install the windshield wiper motor and link with the 2 bolts.
(c) Connect the connector.
(d) Attach the clamp.
4. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
(a) Attach the 10 guides (B).
(b) Attach the 6 claws and guide (A) as shown in the illustration.
(c) Install the 2 clips to the cowl top ventilator louver sub-assembly.
Text in Illustration
5. INSTALL CENTER NO. 2 COWL TOP VENTILATOR LOUVER
(a) Attach the 2 claws and 3 guides to install the center No. 2 cowl top ventilator louver.
6. INSTALL HOOD TO COWL TOP SEAL
7. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
(a) Operate the wiper and stop the windshield wiper motor at the automatic stop position.
(b) When reusing the front wiper arm and blade assembly RH:
(1) Clean the wiper arm serrations.
Text in Illustration
(c) When reusing the windshield wiper link assembly:
(1) Clean the wiper pivot serrations with a wire brush.
(d) Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.
Torque : 25 Nm (255 kgf-cm, 18 ft-lbf)
Standard:
Text in Illustration
HINT
* Hold the wiper arm by hand while tightening the nut.
* Raise and lower the wiper arm a few times to confirm that it has settled to the specified position.
8. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
(a) When reusing the front wiper arm and blade assembly LH:
(1) Clean the wiper arm serrations.
Text in Illustration
(b) When reusing the windshield wiper link assembly:
(1) Clean the wiper pivot serrations with a wire brush.
(c) Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.
Torque : 25 Nm (255 kgf-cm, 18 ft-lbf)
Standard:
Text in Illustration
HINT
* Hold the wiper arm by hand while tightening the nut.
* Raise and lower the wiper arm a few times to confirm that it has settled to the specified position.
(d) Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.
9. INSTALL FRONT WIPER ARM HEAD CAP
(a) Attach the 3 claws to install the wiper arm head cap.
HINT
Use the same procedure described for the LH side.
10. INSTALL FRONT FENDER TO COWL SIDE SEAL LH
(a) Attach the 5 claws to install the front fender to cowl side seal LH.
11. INSTALL FRONT FENDER TO COWL SIDE SEAL RH
HINT
Use the same procedure described for the LH side.
12. INSTALL FRONT FENDER SIDE PANEL PROTECTOR LH
(a) Attach the 3 clips and guide to install the fender side panel.
13. INSTALL FRONT FENDER SIDE PANEL PROTECTOR RH
HINT
Use the same procedure described for the LH side.
14. INSTALL UPPER RADIATOR SUPPORT SEAL Installation
15. INSTALL ENGINE ROOM SIDE COVER LH
(a) Install the engine room side cover with the 4 clips.
16. INSTALL ENGINE ROOM COVER SIDE
(a) Install the engine room side cover with the 4 clips.
17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.