Roof Opening Panel Glass
Roof Opening Panel Glass
This is a "Trustmark Authoring Standards (TAS) Repair Procedure"
- TAS style procedures can be identified by steps that have no accompanying step text and the magenta color of the electrical connectors and fasteners such as nuts, bolts, clamps or clips.
- TAS removal and installation procedures use a sequence of color illustrations to indicate the order to be followed when removing/disassembling or installing/assembling a component.
- Many of the TAS procedures will have the installation information within the removal steps.
- The TAS color illustrations use a variety of symbols to indicate important details of the procedures. It is important to understand these symbols in order to properly used the TAS procedures.
Refer to How to Use TAS Procedures and TAS Symbol Glossary at Vehicle | Description and Operation for additional information on these TAS procedures.
For additional information, refer to How to Use TAS Procedures How to Use TAS Procedures
Removal
NOTE:
Left-hand shown, right-hand similar.
Apply strips of masking tape to the front edge of the fixed rear glass to prevent damage when lifting the glass panel.
NOTE:
This step requires the aid of another technician.
Disable the one-touch operation.
Open the roof panel, while the roof opening panel is moving remove fuse F10.
Replace fuse F10 and make sure the roof opening panel functions without the one-touch operation.
1 Open the roof opening panel blind.
2 Fully open the roof opening panel glass.
NOTE:
Left-hand shown, right-hand similar.
Remove the roof opening panel glass guide locators.
Remove the Torx screw (TX15).
Apply pressure downwards (1) and slide forward (2) and then remove the guide locator (3).
Repeat the operation for the other side.
CAUTION: Do not raise the front end of the roof opening panel glass by more than 100 mm with the rear end located as damage may occur.
NOTE:
This will release the front of the glass panel.
Close the roof opening panel glass to 85 mm and apply upwards pressure to release the front of the glass.
NOTE:
Left-hand shown, right-hand similar.
Slide the connecting bars forward 20 mm.
NOTE:
This step requires the aid of another technician.
Remove the roof opening panel glass.
NOTE:
Do not disassemble further if the component is removed for access only.
Remove the roof opening panel glass connecting bars.
Installation
CAUTION: Make sure that the roof opening panel motor is not operated at any time until instructed.
NOTE:
Left-hand shown, right-hand similar.
Using a non-permanent marker, mark the seal to show the roof opening panel glass driving slider position.
NOTE:
This step is only required if previously removed.
Locate the connecting bar rear guide.
NOTE:
This step is only required if previously removed.
Locate the connecting bar front guide.
NOTE:
Left-hand shown, right-hand similar.
NOTE:
This step is only required if previously removed.
Slide the connecting bars forward 20 mm.
CAUTION: Do not raise the front end of the roof opening panel glass by more than 100 mm with the rear end located as damage may occur.
NOTE:
This step requires the aid of another technician.
Align the rear runners to the roof opening panel channels.
Carefully slide the roof opening panel glass rearward, so that a 85 mm opening is achieved.
NOTE:
Left-hand shown, right-hand similar.
Align the connecting bar with the roof opening panel guide.
CAUTION: Damage will occur if the roof opening glass panel is not aligned correctly.
NOTE:
This step requires the aid of another technician.
NOTE:
Left-hand shown, right-hand similar.
Carefully align and locate the roof opening panel glass to the driving slider.
If resistance is encountered, realign the roof opening panel glass to the driving slider.
CAUTION: Do not apply downward pressure whilst operating the roof opening panel.
NOTE:
A slight noise may be heard when the roof opening panel is operated for the first time.
Carefully retract the roof panel glass rearwards for 50 mm to make sure the roof panel glass is correctly located in the guide rails.
If the roof panel glass is correctly located, fully open the roof panel glass.
Install the panel glass guide locator.
Locate the front of the guide locator (1) and raise upwards (2) and then locate onto the rail and slide forwards (3).
Tighten the Torx screw to 2.5 Nm.
Repeat procedure for the other side.
CAUTION: Make sure the net deflector folds protrude rearwards when closing the roof opening panel glass. If the net deflector is folded forwards water leakage from the roof panel may occur.
Close the roof opening panel glass.
1 Remove the protective tape.
2 Manually initialize the roof opening panel motor.
Switch the ignition on.
Press the front leading edge of the roof opening panel switch and move the roof opening panel glass to the full tilt position.
Release the switch.
Press and hold the front leading edge of the switch.
After 20 seconds the roof opening panel glass will perform the following: stall in the tilt mode causing a noise, a full open and close cycle.
Do not release the switch until the roof opening panel glass has completed the above step.
Release the switch.
The roof panel will now operate one-touch open (tilt and fully open) and one-touch close (from the fully open position).
One touch close is inoperable from tilt.
3 Close the roof opening panel glass.
4 Close the roof opening panel blind.