P0440

Diagnostic Chart:

Wiring Diagram:

Circuit Description
The evaporative system includes the following components:

^ Fuel tank
^ EVAP vent solenoid
^ Fuel tank pressure sensor
^ Fuel pipes and hoses
^ Fuel vapor lines
^ Fuel cap
^ EVAP canister
^ Purge lines
^ EVAP canister purge valve
^ EVAP service port

The evaporative emission system is checked by applying vacuum to the EVAP system and monitoring for a vacuum decay. The PCM monitors the vacuum level through the fuel tank pressure sensor signal.

At an appropriate time, the EVAP canister purge valve and the EVAP vent solenoid are turned ON. allowing the engine to draw a small vacuum on the entire evaporative emission system. After the desired vacuum level has been achieved, the EVAP canister purge valve is turned OFF, sealing the system. It a sufficient vacuum level cannot be achieved, a large leak is indicated. This can be caused by the following conditions:

^ Missing or faulty fuel cap.
^ Disconnected or faulty fuel tank pressure sensor.
^ Disconnected, damaged, pinched, or blocked EVAP purge line.
^ Disconnected or damaged EVAP vent hose.
^ Disconnected, damaged, pinched, or blocked fuel tank vapor line.
^ Disconnected or faulty EVAP canister purge valve.
^ Disconnected or faulty EVAP vent solenoid.
^ Open ignition feed circuit to the EVAP vent or purge solenoid.
^ Damaged EVAP canister.
^ Leaking fuel sender assembly O-ring.
^ Leaking fuel tank or fuel filler neck.

Any of the above conditions can set a DTC P0440.

Conditions for Setting the DTC

^ The Barometric pressure (BARO) is greater than 75 kPa.
^ The intake air temperature is between 5°C and 29°C (41°F and 84°F) at engine start up.
^ The engine coolant temperature is between 5°C and 29°C (41°F and 84°F) at engine start up.
^ Intake Air Temperature is not more than 1°C (2°F) greater than the Engine Coolant Temperature at start up.
^ Engine Coolant Temperature is not more than 7°C (12°F) greater than the Intake Air Temperature at start up.
^ Fuel tank level is between 26% and 74%.
^ The Throttle Position (TP) sensor is between 9 and 35%.
^ The EVAP solenoid is at 50% Pulse Width Modulated (PWM) within 65 seconds of engine run time.
^ The EVAP system is unable to achieve or maintain vacuum during the diagnostic test. The amount of decay will vary with the fuel level.
^ DTCs P0106, P0107, P0108, P0112, P0113, P0117, P0118, P0121, P0122, P0123, P0125, P0131, P0132, P0133, P0134 and P1133 not set.

Action Taken When the DTC Sets

^ The Malfunction Indicator Lamp (MIL) will illuminate.
^ The PCM will record operating conditions at the time the diagnostic fails. The Freeze Frame and Failure Records buffers will store this information.
^ A history DTC is stored.

Conditions for Clearing the MIL/DTC

^ The MIL will turn OFF after one ignition cycle in which the diagnostic runs without a fault.
^ Freeze Frame information and the history DTC will clear after one ignition cycle in which the diagnostic runs without a fault.
^ DTC's can be cleared with battery disconnect.

Diagnostic Aids
Check for the following conditions:

^ A missing, loose, or damage fuel cap.
^ Missing or damaged O-rings at the EVAP canister fuel vapor fittings and the purge line fittings.
^ A cracked EVAP canister.
^ Damaged or disconnected source vacuum line, EVAP purge line, vent hose or fuel tank vapor line.
^ A poor connection at the PCM: Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals.
^ Damaged harness: Inspect the wiring harness to the EVAP vent solenoid, the EVAP purge solenoid, and the fuel tank pressure sensor for an intermittent open or short circuit.
^ A kinked, pinched or plugged vacuum source, EVAP purge, or fuel tank vapor line. Verify that the lines are not restricted.

Check for charcoal particles. Refer to Carbon Particle Removal from EVAP System before starting repairs. Service and Repair

Reviewing the Fail Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to set occurs. This may assist in diagnosing the condition.

Test Description
Number(s) below refer to the step number(s) on the Diagnostic Table.

1. The Powertrain OBD System Check prompts the technician to complete some basic checks and store the freeze frame and failure records data on the scan tool if applicable. This creates an electronic copy of the data taken when the malfunction occurred. The information is then stored on the scan tool for later reference.
4. If a vent solenoid or EVAP canister purge valve electrical malfunction is present, the purge system will not operate correctly. Repairing the electrical malfunction will very likely correct the condition that set DTC P0440.
5. Checks the fuel tank pressure sensor at ambient pressure.
7. Forces the fuel tank pressure sensor to re-zero.
8. Determines whether or not the EVAP system is sealed sufficiently to be pressurized. If not, the large leak must be located and corrected before continuing with diagnosis.
9. Verifies that the fuel tank pressure sensor accurately reacts to EVAP system pressure changes.
13. Checks for a stuck closed EVAP canister purge valve.
12. Ensures that sufficient source vacuum is present at the EVAP canister purge valve.
20. Insures proper system integrity.