Inspection

INSPECTION

1. HEADLAMP DIMMER SWITCH ASSY
a. Inspect light control switch continuity.







1. Check that there is continuity between terminals at each switch position as shown in the chart.

b. Inspect headlight dimmer switch continuity.







1. Check that there is continuity between terminals at each switch position as shown in the chart.

HINT: Turn headlight dimmer switch to the HEAD position when checking "LOW BEAM" and "HI BEAM".

c. Inspect turn signal switch continuity.







1. Check that there is continuity between terminals at each switch position as shown in the chart.

d. w/ Fog light:
Inspect front fog light switch continuity.







1. Check that there is continuity between terminals at each switch position as shown in the chart.

2. BACK UP LAMP SWITCH ASSY
a. Inspect back up lamp switch continuity.
1. Check that there is continuity between terminals when switch is operated.

Standard:
OFF (When ball is not pressed): No continuity
ON (when ball is pressed): Continuity







3. STOP LAMP SWITCH ASSY
a. Inspect stop lamp switch assy continuity.
1. Disconnect the stop lamp switch assy connector.
2. Check that there is continuity between terminal 1 and 2.







4. HAZARD WARNING SIGNAL SWITCH ASSY
a. Inspect hazard warning signal switch continuity.
1. Check that there is continuity between terminal 1 and 2 when switch is operated.

b. Inspect illumination operation.
1. Connect the positive (+) lead from the battery to terminal 4 and negative (-) lead to terminal 3, then check that the illumination comes on.

5. FRONT DOOR COURTESY LAMP SWITCH ASSY
a. Inspect front door courtesy lamp switch assy continuity.
1. Check that there is continuity between terminal 1 and body ground when switch is operated.

Standard:
ON (When shaft is pressed): No continuity
OFF (When shaft is not pressed): Continuity

6. REAR DOOR COURTESY LAMP SWITCH ASSY
a. Inspect rear door courtesy lamp switch assy continuity.
1. Check that there is continuity between terminal 1 and body ground when switch is operated.

Standard:
ON (When shaft is pressed): No continuity
OFF (When shaft is not pressed): Continuity

7. LUGGAGE COMPARTMENT ROOM COURTESY LAMP SWITCH ASSY
a. Inspect luggage compartment room courtesy lamp switch assy continuity.
1. Check that there is continuity between terminal 1 and bracket when switch is operated.

Standard:
ON (When shaft is pressed): No continuity
OFF (When shaft is not pressed): Continuity







8. MAP LAMP ASSY
a. Inspect map lamp assy continuity.
1. Check that there is continuity between terminal 1 and 3 when switch is operated.

9. ROOM LAMP ASSY NO.1
a. Inspect room lamp assy No.1 continuity.
1. Check that there is continuity between terminals when switch is operated.

Standard:
ON: Continuity
OFF: No continuity

10. LUGGAGE COMPARTMENT LAMP ASSY NO.1
a. Inspect luggage compartment lamp assy No.1 continuity.
1. Check that there is continuity between terminals when switch is operated.

Standard:
ON: Continuity
OFF: No continuity







11. HEADLAMP RELAY
a. Inspect headlamp relay continuity.
1. Check that there is continuity between terminals.
2. Apply battery voltage (10 - 14 V) between terminal 1 and 2, then check that there is continuity between terminal 3 and 5

Standard: There is continuity.







12. FOG LAMP RELAY
a. Inspect fog lamp relay continuity.
1. Check that there is continuity between terminals.
2. Apply battery voltage (10 - 14 V) between terminal 1 and 2, then check that there is continuity between terminal 3 and 5.

Standard: There is continuity.







13. TAILLAMP RELAY
a. Inspect tail lamp relay continuity.
1. Check that there is continuity between terminals.
2. Apply battery voltage (10 - 14 V) between terminal 1 and 2, then check that there is continuity between terminal 3 and 5.

Standard: There is continuity.

14. INTEGRATION RELAY
a. Check illuminated entry operation.
1. Connect the positive (+) lead from the battery to terminal A-1 and negative (-) lead to terminal A-9.
2. Check that the battery voltage (10 - 14 V) generates between terminal B-3 and A-9, then connect the negative (-) lead from the battery to terminal A-5 and A-6.
3. Disconnect the negative (-) lead from the battery to terminal A-5 and A-6, or connect the positive (-) lead from the battery to terminal B-18 or B-19, or connect the positive (+) lead from the battery to terminal A-10 then check that there is no voltage between terminal A-12 and A-9.

b. Inspect battery saver operation.
1. Connect the positive (+) lead from the battery to terminal A-1 and negative (-) lead to terminal A-9.
2. Connect the negative (-) lead from the battery to terminal A-5 and A-6, then check that the battery voltage (10 - 14 V) generates between terminal A-12 and A-9.




3. After 20 mm., check that there is no voltage between terminal A-12 and A-9.