Campaign - Cold Start Valve/Time Switch Wiring
SUBJECT COLD START VALVE THERMAL AND TIME SWITCH NUMBER: 86-E-02WIRING HARNESS INTERCHANGED
DATE: August 1, 1986
MODELS/YEARS 1986 CUTLASS CIERA MODELS EQUIPPED WITH SECTION: 6D
A 2.8L MPFI (VIN CODE W) ENGINE
CONDITION
General Motors has determined that some 1986 Oldsmobile Cutlass Ciera models equipped with a 2.8L MPFI (VIN Code W) engine may have two circuit wires interchanged in the cold start valve thermal and time switch.
This can result in a grounding of the cold start injector power circuit. This grounding can blow the 10 amp fuse in the "crank" cavity. If this occurs, the cold start injector will not operate, causing a difficult or no start condition.
To correct this condition, the circuit wires are to be inspected and, if required, reversed and the "crank" fuse replaced per instructions in this bulletin.
VEHICLES INVOLVED
A total of 16 Oldsmobile Cutlass Ciera models equipped with a 2.8L MPFI (VIN Code W) engine are involved in this campaign. Vehicle identification numbers of involved vehicles are listed below:
1G3AJ35W0GD300009 1G3AJ35W9GD301062
1G3AJ35W7GD300010 1G3AJ35W9GD301160
1G3AJ35W2GD300500 1G3AJ35W8GD301280
1G3AJ35W1GD300620 1G3AJ35W2GD301419
1G3AJ35WXGD300700 1G3AJ35W0GD301581
1G3AJ35W3GD300747 1G3AJ35W2GD301601
1G3AJ35W1GD300827 1G3AJ35W7GD302064
1G3AJ35W5GD300880 1G3AJ35W1GD302416
DEALER ACTION
Dealers are to service all vehicles subject to this campaign at no charge to owners, regardless of mileage, age of vehicle, or ownership, from this time forward.
Whenever a vehicle subject to this campaign is taken into your new or used vehicle inventory, or it is in your dealership for service in the future, you should take the steps necessary to be sure the campaign correction has been made before reselling or releasing the vehicle.
Owners of vehicles recently sold from your new vehicle inventory are to be contacted by the dealer and arrangements made to make the required modification according to instructions contained in this bulletin.
SERVICE PROCEDURE
1. Open hood.
2. Disconnect negative battery cable.
3. Remove connector from cold start valve thermal and time switch (see Figure 1).
4. Pull rubber boot back from terminal, inspect for proper wire routing (see Figure 2); if correct go to step 8.
5. Remove terminals from connector body.
6. Reinstall terminals, making sure the position is the same as shown in Figure 2.
7. Replace the "crank" fuse (see Figure 3).
8. Reconnect negative battery cable.
9. Start engine; then check "crank" fuse to assure correct wiring.
10. Install Campaign Identification Label and close hood.
CAMPAIGN IDENTIFICATION LABEL INSTALLATION
Each vehicle modified in accordance with the instructions outlined in this procedure will require a Campaign Identification label. Each label provides a space to include the campaign number, the
(5) digit dealer code of the dealer performing the campaign service, and the date vehicle was campaigned. This information may be inserted with a typewriter or ballpoint pen. When installing label, clean the surface of the radiator upper mounting support and apply the campaign label where it is readily visible.
PARTS INFORMATION
Parts required to complete this modification are to be obtained from the Warehousing and Distribution Division of General Motors (WDDGM). To ensure that these parts will be obtained as soon as possible, they should be ordered from WDDGM on a C.I.O. order with no special instruction code but on an advise code (2).
Part Number Description Quantity
12004007 10 Amp Mini Fuse 1
CLAIM INFORMATION
Operation Failure Code Labor Operation Labor Hours
Inspect - No Further Action
Required 96 V3430 .2
Inspect - Reverse Circuit Wires and
Replace Fuse 96 V3431 .2