A/T - LA4AEL Exchange Program
Bulletin No.: 005/93Issued: 9/15/93
Revised
Category
K2
Applicable Model/s
1994 626/MX-6
with 4 Cyl., A/T
Subject:
EXCHANGE PROGRAM FOR LA4AEL TRANSAXLES
APPLICABLE MODELS/VINS
1994 626/MX-6 (with 4 cyl. engines and automatic transaxles) from vehicle introduction through August 31, 1994
DESCRIPTION
An exchange program has been established for the first year of service on the new LA4AEL transaxle. This transaxle is used in 1994 626/MX-6 (4cyl.) models. This program will provide quick response to customer complaints and feed back information leading to early transaxle failure.
The program is effective from the time of vehicle introduction through August 31, 1994. During this period, the preferred method for repairing automatic transaxle failure is replacement.
A Technical Assistance Center and toll free "800" number have been established to administer the program. Assistance will be available Monday through Friday (except holidays) 8 a.m. to 5 p.m. (EST by dialing 1 800 820-6262. If you hear a recording, leave a message and a technical assistant will return your call.
NOTE:
Exchange units are shipped with the following materials:
Shipping plugs to prevent ATF spills during transportation (transaxles sent by ground transportation will have ATF installed)
Information packets containing "Installation Instructions", "Core Return Instructions", "Bill of Lading" and an "Information Return Card".
Confirm that the above material is in the exchange unit information package. If not, call the "800" number for replacement.
REPAIR PROCEDURE
1. When you have determined that an exchange unit may be needed, be sure you have performed the following diagnostics and record the findings on the diagnostic recording form as shown.
a) Check ATF level at normal operating temperature. If low, fill to the proper level and check for leaks.
NOTE:
If leaks are found, call the Technical Assistance Center at 1 800 820-6262 prior to repair.
b) Test drive the vehicle to verify the customer complaint.
c) Check harness connectors for proper installation at the following locations:
- Manual Level Position Sensor (MLP)
- Turbine Shaft Speed Sensor JSS)
- Vehicle Speed Sensor (VSS)
- Transaxle Solenoid Body Connector
NOTE:
If no problems are found, perform steps "d" through f". If the connectors are disconnected, reconnect and verify that the complaint is fixed. If the complaint is not fixed, perform steps "d" through "f".
d) Retrieve fault codes using the "Quick Test" and the Super Star II Tester (P/N 49 UN01 056)
e) Perform the pin point test on any fault codes found. Refer to section K2 of the workshop manual.
NOTE:
Repair only those codes that indicate problems outside the transaxle.
f) If the fault codes indicate internal transaxle failure, confirm codes using the LA4AEL transmission tester, harness and overlay (P/N 49 UN01 71, 089, 090, 091, and 092).
2. Call the Technical Assistance Center at 1 800 820-6262 and provide the following:
- Dealer Name, Shipping Address, Telephone Number and Dealer Code
- Vehicle VIN, Date of Retail Sale and Mileage
- Repair Order Number
- Transaxle Identification Tag Information [Serial Number, Model Number, Build Date and Assembly Part Number (Includes Prefix and Suffix)]. Refer to the illustration shown.
- All Diagnostic Findings
3. Remove and replace the transaxle assembly according to the instructions contained in the exchange unit information packet.
NOTE:
The exchange unit is delivered with a torque converter.
Exchange units with ATF installed are shipped by ground transportation.
Transaxle mounts and the dipstick must be removed from the original transaxle and installed on the exchange unit.
4. Flush the transaxle cooling system according to the instructions in the exchange unit information packet.
NOTE:
Do not use high pressure air to remove debris from the cooling system.
5. After installation, check the ATF fluid level at normal operating temperature.
6. Prepare the original transaxle (core) for return. Follow the instructions provided in the exchange unit information packet.
7. Fill in the required information on the "Return Information Card".
PARTS INFORMATION
The Technical Assistance Center will arrange exchange unit shipping.
1. Allow 3 to 5 days for delivery of the exchange unit.
NOTE:
If the exchange unit is not delivered after 5 days, contact the Technical Assistance Center at 1 800 820-6262.
2. Inspect the return core for installation of shipping plugs (including oil fill tube plug), torque converter and "Return Information Card".
3. Ship the return core by truck (freight collect) using the bill of lading contained in the exchange unit information packet. Cores will be returned to:
Batavia Transaxle Plant
1981 Front Wheel Drive
Batavia, Ohio 45103
NOTE:
Dealers will be contacted 2-5 days after delivery to confirm delivery of the exchange unit and return of the core. Dealers must return the complete assembly and shipping container.
Failure to return a complete assembly (including torque converter and exchange unit shipping container) within 15 days will result in a debit to the dealer in the amount equal to a new transaxle.
WARRANTY INFORMATION
(Applies to 1994 626/MX-6 with 4cyl. engine from introduction through August 31, 1994)
Warranty Type: A
Customer Comment Code: 24 or 29
Damage Code: 99
Part Number Main Cause: 5555 93 LA4A (Exchange transaxle is provided at no cost, Includes $100.00 reimbursement for handling allowance, no 30 percent mark-up).
Quantity: 1
Related Parts: List parts necessary to complete the repair
Operation Number/Labor Hours: K0001XDX/0.8Hrs. (Diagnostic Steps 1 through 4)
K0002XDX/1.1Hrs. (Diagnostic Steps 5 and 6)
K0101DRX/3.8Hrs. (Transaxle R&R)
YY0110RX/0.3Hrs. (Administration)
NOTE:
Exchange units are warranted for the remainder of the vehicle's original 36 month/50000 mile limited warranty.